Sommario  Guida in linea MOBOTIX

MxAnalytics

Notes

MxAnalytics allows tracking objects that move about in the image and to collect statistical information about these objects. To do so, the camera records the distribution of the objects and can present the results as a heatmap. In addition, you can define counting corridors, which are counting the objects that are passing through. These data are recorded in a reserved partition on a storage device that is directly attached to the camera. Note that the storage device needs to be partitioned accordingly when formatting the device in the Storage on External File Server / Flash Device dialog (see also MxAnalytics Data Storage on this page).

In order to use MxAnalytics, you need to configure this feature in the General MxAnalytics Settings dialog. After that, you can view the results in the MxAnalytics Overview dialog and export the data in different formats.

Notes

Applications

In order to get reliable results, you should make sure to avoid all external influences that may degrade the results of MxAnalytics. If this is not possible, the results may be inaccurate. The following influences can lead to unreliable results of MxAnalytics:

MxAnalytics has been designed for cameras mounted to a ceiling. Depending on the lens used, the camera should be mounted no lower and no higher than shown in this table:

Lens

Minimum Height

Maximum Height

L12 (1,8 mm)

2.5 m

6 m

L23 (3.6 mm), L25 (4.0 mm)

6 m

10 m

Configuring MxAnalytics in the General MxAnalytics Settings dialog follows these steps:
To view the results of MxAnalytics, open the MxAnalytics Overview dialog:

The "General MxAnalytics Settings" Dialog

General Settings

You can arm MxAnalytics permanently or use signal inputs and time table profiles to control the arming status.

Example 1. Scenario

In order to activate MxAnalytics only during the operating hours of a store, you need to create a Time Table Profile that matches the opening hours. Next, set the arming of MxAnalytics to Enabled and select the time table profile with the opening hours you just defined.

Tip

Using a time table profile to control the arming status of MxAnalytics reduces the storage space required and thus enlarges the time span covered by the collected data. This also improves the significance of the results, since objects outside of the analysis window are ignored and do not appear in the heatmap. For more information on the storage space, see Storage Requirements below.

Detection Settings

This sections contains general settings for object recognition.

Detection Area

In order to limit the analysis of MxAnalytics to a specific area, you can define several windows or polygons in this field. The most convenient method to define such a window is to use a [Shift]-click, click to define a rectangle in the live image, then click on Add detection area (see also Graphically Entering Image Areas). Note that it is also possible to exclude specific areas from detection.

Rectangle Syntax

[!]image sensor, horizontal coordinate, vertical coordinate, width, height

(optional parameters have square brackets)

Example 2. Rectangle Syntax
0,0,0,1280,960

Polygon Syntax

[!]image sensor, poly=<hor. coordinate>x<vert. coordinate>
 /<hor. coordinate>x<vert. coordinate>/<hor. coordinate>x<vert. coordinate>
 {/<hor. coordinate>x<vert. coordinate}

(optional parameters have square brackets, parameters that can be used as often as needed have curly brackets)

Example 3. Polygon Syntax
0,poly=0x0/0x1280/960x1280/960x0

Notes

  • In order to exclude a specific area from detection, enter a "!" in front of the definition line.

  • All detection areas refer to the entire image sensor.

  • If a counting corridor is outside of the detection area, the area will be enlarged automatically. This is indicated by color − it changes to magenta.

Tips

  • Limiting the detection area increases performance and delivers better results. in addition, doing so reduces the storage space required and thus enlarges the time span covered by the collected data. For more information on the storage space, see Storage Requirements below.

  • Image areas with reflecting surfaces should be excluded from detection to prevent negative influences on the analysis results.

    If you are activating the display of the detection area, the camera shows the detection areas (rectangles and polygons) as well as the bounding box (the polygon containing all detection areas in the camera image).

Mounting Height

Enter the height in centimeters from the floor to the mounting position of the camera. The camera uses this information to properly display the results in the heatmap. When analyzing moving persons, the heatmap will be shown near the persons' feet.

Note

Mounting the camera at heights of less than 2 m/6 ft will reduce the accuracy of the analysis results.

Tilt Angle

Sets the tilt angle for this camera. If mounted to the ceiling, select −90°, if mounted to the wall, select . The camera uses this information to properly display the results in the heatmap.

Minimum Object Size

This parameter allows setting a minimum object size in pixels (smaller objects are ignored). The most convenient method is to use a [Shift]-click, click to define a rectangle in the live image, then click on Set minimum size (see also Graphically Entering Image Areas).

Light and Shadow

The camera provides three pre-defined settings to adapt the camera to the illumination profile at the location. In addition, you can select a custom setting to manually adjust the light and shadow settings of the camera.

Available Settings
  • Artificial light, no shadows: Select this setting if the detection area is only illuminated by artificial light and objects are not casting shadows when moving.

  • Sparse sunlight, blurred shadows: Select this setting if the illumination of the detection area changes only slightly (e.g. by sunlight) and objects are only casting blurred (i.e., not well-defined) shadows when moving.

  • Heavy sunlight, well-defined shadows: Select this setting if the detection area is subjected to heavy changes in illumination (e.g. due to large windows) and objects are casting well-defined shadows when moving.

  • Custom size: This setting allows choosing between three exposure programs and two methods for shadow detection:

    • Constant illumination: Select this option if the illumination of the detection area does not change. An example for such a scene would be a hall without windows. This option also allows following objects that stop for several seconds. Since this option requires the least computing time, the camera achieves the highest frame rates.

    • Slowly changing illumination: This option is suitable for rooms that have only a few windows and illumination changes only slightly and not abruptly. An example for such a scene would be a room with few narrow windows close to the ceiling.

    • Fast changing illumination: Select this option for rooms with strong changes in illumination, e.g. in rooms with large panorama windows. Since this option requires the most computing time, the camera generates images with lower frame rates. This option does not allow changing the shadow detection settings.

    • Shadow Detection: Shadows can lead to distortions in the MxAnalytics results. In order to avoid these distorted analysis results, you can activate these additional methods for shadow detection:

      • Coarse structure/dark background: Use this option if the background of the scene is coarsely structured or dark.

      • Fine structure/light background: Use this option if the background of the scene is finely structured or light. This option provides three sensitivity levels (Low, Medium, High). The higher the sensitivity, the more shadows will be removed from the image. At the same time, however, chances are rising that objects are also recognized as shadows.

Sensitivity

This parameter controls the sensitivity of the analysis. A higher value means that the software only recognizes objects that have a noticeable color difference to the background. A lower value means that the software also recognizes objects that are hard to recognize against the background.

Object Display Settings

The following settings for displaying objects in MxAnalytics are available:

  • Bounding Box: Shows the bounding box if you select a color.

  • Object Track: Shows the object tracks if you select a color. The track follows the object's center of gravity.

  • Object Halo: Colors the objects if you select a color. An additional parameter controls the transparency of the objects.

Counting Corridor Settings

A counting corridor is used to count objects that are passing through the corridor. Note that software also recognizes the direction of movement of these objects. Each line in the definition field represents one counting corridor. The definition of a counting corridor consists of its start and end points and its width.

Syntax of a Counting Corridor Definition

image sensor,start=<hor. coordinate>x<vert. coordinate>,
 end=<hor. coordinate>x<vert. coordinate>,width=<width>,
 id=<identification number>[,name=<string>][,north=<string>]
 [,south=<string>]

(optional parameters have square brackets)

Example 4. Syntax of a Counting Corridor Definition
0,start=800x440,end=800x520,width=360,id=1,name=Eingang EG\, links,north=Hinein,south=Hinaus

Notes

  • If the string contains a comma, you need to precede it with a backslash (\).

  • You can define up to 16 counting corridors for one camera.

  • The IDs can be in the range from 0 to 65535.

Parameter

Description

Image sensor

Selects the image sensor (camera image) to use for this counting corridor definition:

  • 0: Right camera image on dual cameras, default setting on mono cameras.

  • 1: Left camera image on dual cameras.

start

Start coordinate of the counting corridor, defined by its horizontal and vertical coordinate.

end

End coordinate of the counting corridor, defined by its horizontal and vertical coordinate.

width

Width of the counting corridor.

id

The identification number (ID) of the corridor shown in the image. You can thus visually identify the corridors.

name

The name of the corridor (e.g. "South Entrance") that will be shown in the report later on.

(Optional parameter)

north

The description of objects passing through the corridor in the direction of the arrow/north (e.g. "In") that will be shown in the report later on.

(Optional parameter)

south

The description of objects passing through the corridor in the opposite direction of the arrow/south (e.g. "Out") that will be shown in the report later on.

(Optional parameter)

Graphically Entering Counting Corridors

In order to draw a counting corridor in the live image, keep [Ctrl+Shift] pressed and click in the live image. In order to define the direction and length of the counting corridor, hold down the [Ctrl] key and click again into the live image. The next click sets the width of the counting corridor. Then click on the button in the dialog to add the counting corridor definition to the corresponding definition field.

Counting Corridor Style

The software provides the following settings to show the corridors in the camera image:

  • Off: The camera never shows the counting corridors.

  • On: The camera always shows the counting corridors.

  • On and hide on counting: The camera shows the counting corridors. Once an object has passed through the corridor, the camera briefly hides the corridor.

  • On and highlight on counting: The camera shows the counting corridors. Once an object has passed through the corridor, the camera briefly highlights the corridor by changing its color.

  • Off and highlight on counting: The camera hides the counting corridors. Once an object has passed through the corridor, the camera briefly shows the corridor.

Text Color

Allows setting a color for the counters and the corridor IDs.

Heatmap Settings

A heatmap shows the distribution of the objects, i.e., where objects are staying and how they move, as a colored heat image. The warmer the color, the more objects are staying at a specific location. When analyzing moving persons, the heatmap will be shown near the persons' feet.

Reference Image

If you want to always use the same image as a background for the heatmap, you can save a "reference image" in the camera. If no reference image has been saved or you deleted an existing reference image by clicking on Delete, the software uses the current live image of the camera as background.

  • Save: Saves the current live image as a reference image (background) for displaying the heatmap.

  • Show: Shows the saved reference image in a new window. If no reference image has been saved or an existing one has been deleted, this button is deactivated.

  • Delete: Deletes the saved reference image. If no reference image has been saved or an existing one has been deleted, this button is deactivated.

Tip

You should save a reference image if no objects are visible in the live image. This avoids that objects are interfering with the display of the heatmap later on.

Live Image Display

Shows the current heatmap on the live image of the camera. This feature is mainly aimed at quickly checking the configuration.

Caution

You should only briefly show the heatmap in the camera's live image, since this feature generates high CPU loads and results in reduced live image rates of the camera. Before closing the dialog, you should make sure that you deactivate the Show Heatmap checkbox and that you save the changes permanently by clicking on Set/Close at the bottom of the dialog.

Note

While you are displaying the heatmap in the camera image, the heatmap will also show on the recorded image (except when using the Full Image recording mode).

The "General MxAnalytics Settings" Dialog

Open the MxAnalytics Overview dialog to define the reports that are to be generated by the camera:

Status

This section of the dialog contains general information about the records that are available. The information covers the date/time of the first and last records as well as information on the storage space used and the total number of records. In addition, you can manually create a new record (Force new record) and reset MxAnalytics completely by deleting all records (Delete all records).

Notes

  • Once you have clicked on Delete all records and acknowledged the system prompt, you cannot undo the deletion.

  • Deleting the records can take several minutes, depending on the size of the MxAnalytics partition on the storage device.

Heatmap

Click on Show to get a heatmap based on the current data in a separate browser window. The heatmap contains the MxAnalytics results since the last reset of the data or since activating MxAnalytics (whichever is applicable).

Counting Corridors

This section contains a summary table of the defined counting corridors, their descriptions and the current counter values.

Tip

You can use other programs to get the current counting corridor configuration and the current counter values using the following link: http://192.168.1.221/control/stat_export?function=counter. The data are returned in JSON format.

Counting Corridor Report Profiles

This section contains a summary table of the defined counting corridor report profiles. If no report profiles have been defined yet, you can do so in the Counting Corridor Report Profiles dialog.

  • Name: Click on a profile name to get the corresponding counting corridor report in a separate browser window.

  • Export Range: Shows the time range of the report to be exported.

  • Email Profile: Indicates whether or not this report profile is used in one of the email profiles and if a corresponding time task event exists:

    • This report profile is used in one of the email profiles and a time task event.

    • This report profile is used in one of the email profiles. A corresponding time task event does not exist.

    • This report profile is used in one of the email profiles. The corresponding time task event has been deactivated.

    • This report profile is used in one of the email profiles and a corresponding time task event does not exist.

    Click on the left status LED to create a new email profile or to edit an existing profile.

    Click on the right status LED to create a new time task or to edit an existing task.

  • FTP Profile: Indicates whether or not this report profile is used in one of the FTP profiles and if a corresponding time task event exists:

    • This report profile is used in one of the FTP profiles and a time task event.

    • This report profile is used in one of the FTP profiles. A corresponding time task event does not exist.

    • This report profile is used in one of the FTP profiles. The corresponding time task event has been deactivated.

    • This report profile is used in one of the FTP profiles and a corresponding time task event does not exist.

    Click on the left status LED to create a new FTP profile or to edit an existing profile.

    Click on the right status LED to create a new time task or to edit an existing task.

  • IP Notify Profile: Indicates whether or not this report profile is used in one of the IP Notify profiles and if a corresponding time task event exists:

    • This report profile is used in one of the IP Notify profiles and a time task event.

    • This report profile is used in one of the IP Notify profiles. A corresponding time task event does not exist.

    • This report profile is used in one of the IP Notify profiles. The corresponding time task event has been deactivated.

    • This report profile is used in one of the IP Notify profiles and a corresponding time task event does not exist.

    Click on the left status LED to create a new IP Notify profile or to edit an existing profile.

    Click on the right status LED to create a new time task or to edit an existing task.

Tip

If you want the camera to automatically send a counting corridor report via email, FTP or IP Notify, make sure that both status LEDs in the corresponding line (Profile and Time Task) are green. If this is not the case, create a new email profile, FTP profile or IP Notify profile and then add a new time task for this profile.

Heatmap Report Profiles

This section contains a summary table of the defined heatmap report profiles. If no report profiles have been defined yet, you can do so in the Heatmap Report Profiles dialog.

  • Name: Click on a profile name to get the corresponding heatmap report in a separate browser window.

  • Export Range: Shows the time range of the report to be exported.

  • Email Profile: Indicates whether or not this report profile is used in one of the email profiles and if a corresponding time task event exists:

    • This report profile is used in one of the email profiles and a time task event.

    • This report profile is used in one of the email profiles. A corresponding time task event does not exist.

    • This report profile is used in one of the email profiles. The corresponding time task event has been deactivated.

    • This report profile is used in one of the email profiles and a corresponding time task event does not exist.

    Click on the left status LED to create a new email profile or to edit an existing profile.

    Click on the right status LED to create a new time task or to edit an existing task.

  • FTP Profile: Indicates whether or not this report profile is used in one of the FTP profiles and if a corresponding time task event exists:

    • This report profile is used in one of the FTP profiles and a time task event.

    • This report profile is used in one of the FTP profiles. A corresponding time task event does not exist.

    • This report profile is used in one of the FTP profiles. The corresponding time task event has been deactivated.

    • This report profile is used in one of the FTP profiles and a corresponding time task event does not exist.

    Click on the left status LED to create a new FTP profile or to edit an existing profile.

    Click on the right status LED to create a new time task or to edit an existing task.

  • IP Notify Profile: Indicates whether or not this report profile is used in one of the IP Notify profiles and if a corresponding time task event exists:

    • This report profile is used in one of the IP Notify profiles and a time task event.

    • This report profile is used in one of the IP Notify profiles. A corresponding time task event does not exist.

    • This report profile is used in one of the IP Notify profiles. The corresponding time task event has been deactivated.

    • This report profile is used in one of the IP Notify profiles and a corresponding time task event does not exist.

    Click on the left status LED to create a new IP Notify profile or to edit an existing profile.

    Click on the right status LED to create a new time task or to edit an existing task.

Tip

If you want the camera to automatically send a heatmap report via email, FTP or IP Notify, make sure that both status LEDs in the corresponding line (Profile and Time Task) are green. If this is not the case, create a new email profile, FTP profile or IP Notify profile and then add a new time task for this profile.

The "Counting Corridor Report Profiles" Dialog

A counting corridor is used to count objects that are passing through the corridor. Note that software also recognizes the direction of movement of these objects.

Open this dialog to define different reports (weekly/monthly), which can be used in other dialogs. You can then send these reports via email or request them using MxManagementCenter, MxEasy, MxControlCenter or via the camera's remote control (control command, videomotionanalysis section).

Test Profile/Get Report

This section allows testing the profiles listed in this dialog. Select the desired profile and the week, then click on Get report. The camera shows the results in a new window (one table per counting corridor), which can be printed immediately. If you click on Download as CSV table, you can download the file and process the corresponding table in other programs (spreadsheet, databases, etc.).

Profiles & Options

The following parameters are displayed for each profile:

Parameter

Description

Profile

Name of the profile, as it is displayed in other selection boxes.

Counting Corridors

Selects the counting corridors to include in the report.

Columns

Defines the columns of the report table. Each column can show one day or a range of subsequent days to show totals (e.g. Mon − Fri and Sat − Sun).

Export Range

Specifies the range to be included in the report (weekly or monthly report).

Week/Month

Depending on the selection in the Export Range section, you chose to include the current or the last week, or the current or the last month, respectively, in the report.

Time

Selects the time range per day that is to be included in the report.

Export Format

If the report is sent via email, you can chose to attach the file either as HTML or as CSV file.

Report Title

Enter the title of the generated report. You can also use dynamic text containing Variables. Besides the standard variables, you can use additional special variables that are exclusively available for counting corridor report profiles. For an example of how these options can be used, see the Example for Dynamic Text in Report Titles below.

Example for a Weekly Report

A weekly report shows a table in which one line contains the counter values for one hour.

Example 5. Weekly report with the columns Mon,Tue,Wed,Thu,Fri,Mon - Fri and a daily range of 08:00 - 20:00

Counting Corridor Report ... - South Entrance

Time

Monday

Tuesday

Wednesday

Thursday

Friday

Monday - Friday

In

Out

In

Out

In

Out

In

Out

In

Out

In

Out

8:00 - 9:00

0

0

0

0

0

0

4

5

0

0

4

5

9:00 AM - 10:00 AM

0

0

0

0

0

0

5

10

0

0

5

10

10:00 AM - 11:00 AM

0

0

0

0

0

0

1

13

0

0

1

13

11:00 AM - 12:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

12:00 PM - 1:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

1:00 PM - 2:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

2:00 PM - 3:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

3:00 PM - 4:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

4:00 PM - 5:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

5:00 PM - 6:00 PM

0

0

0

0

0

0

0

0

0

0

0

0

6:00 PM - 7:00 PM

0

0

0

0

2

7

0

0

0

0

2

7

7:00 PM - 8:00 PM

0

0

0

0

0

2

0

0

0

0

0

2

Total

0

0

0

0

2

9

10

28

0

0

12

37

Example for a Monthly Report

A monthly report shows a table in which one line contains the counter values for one calendar week.

Example 6. Monthly report with the columns Mon,Tue,Wed,Thu,Fri,Mon - Fri and a daily range of 08:00 - 20:00

Counting Corridor Report ... - South Entrance

Week

Monday

Tuesday

Wednesday

Thursday

Friday

Monday - Friday

In

Out

In

Out

In

Out

In

Out

In

Out

In

Out

31

78

79

89

79

82

81

82

96

80

72

411

407

32

75

69

81

87

82

85

75

80

66

91

379

412

33

79

76

84

95

83

79

102

80

81

75

429

405

34

86

89

92

89

74

87

84

85

91

79

427

429

35

81

88

93

77

0

0

0

0

0

0

174

165

Note

A hyphen in a cell means that there are no counter values available for this hour. This may be caused by an analysis that had been activated at the time or a time range in the past, for which the corresponding data record is not available any more.

Variable Description

Variable

Description

Note

REPORT: Current report

$(REPORT.TIME)

Time span of the current report

Weekly report WW/YYYY (YYYY-MM-DD − YYYY-MM-DD)

Monthly report: Month YYYY

CORRIDOR: Selected corridor

$(CRD.ID) $(CORRIDOR.ID)

Displays the ID of the current counting corridor.

 

$(CRD.NAME) $(CORRIDOR.NAME)

Displays the name of the current counting corridor.

 

Examples for Dynamic Text in Report Titles

Using variables and placeholders, the camera can dynamically integrate information into the report titles.

Scenario

You want to show the camera name and the timestamp in the report title.

Definition of the title

Counting Corridor Report − $(REPORT.TIME) − $(CORRIDOR.NAME) − $(id.nam)

Explanation

$(id.nam)

Name of the camera

$(TMS)

Current timestamp

The "Heatmap Report Profiles" Dialog

A heatmap shows the distribution of the objects, i.e., where objects are staying and how they move, as a colored heat image. The warmer the color, the more objects had been staying at a specific location. When visualizing the results, you can set a range of minimum and maximum values to include in the heatmap, and you can set the heatmap's transparency.

Open this dialog to define different reports, which can be used in other dialogs. You can then send these reports via email or request them using MxManagementCenter, MxEasy, MxControlCenter or via the camera's remote control (control command, videomotionanalysis section).

Custom Report

This section allows getting a heatmap that covers a given time range within the range of recorded data. Firs, select the desired time range for the heatmap. Click on Get report to show this heatmap in a separate browser window.

Tip

Click in a date field to show a calendar. The days with available data have a light green background and can be selected.

Test Profile/Get Report

This section allows testing the profiles listed in this dialog. To do so, select the desired profile and the day, then click on Get report. The distribution of objects is shown in a new window on a current live image of the camera or a reference image (if such an image has been saved; see reference image). You can print the heatmap from this window or save the heatmap as JPG file.

Profiles & Options

The following parameters are displayed for each profile:

Parameter

Meaning

Profile

Name of the profile, as it is displayed in other selection boxes.

Export Range

Specifies the range to be included in the report (current or last day).

Time

Selects the time range per day that is to be included in the report.

Legend

Adds a legend to the image on the heatmap report, which includes the minimum and maximum values in O/h (Objects/hour).

Value Range

Usually, you will display all values in the heatmap (minimum value = 0%, maximum value = 100%). By adjusting the minimum and maximum values, you can influence the displayed results as follows:

  • Minimum Value: If you enter a value greater than 0 in the left field, the areas with less traffic are not shown in the heatmap image.

  • Maximum Value: If you enter a value less than 100 in the right field, the areas with more traffic are highlighted even more in the heatmap image. This done by displaying all values equal or higher than the adjusted maximum value in the color of the maximum (red).

Transparency

Controls the heatmap transparency. A higher value will show more of the image in the background.

Additional Information

MxAnalytics Data Storage

In order to to use the export features of MxAnalytics, the camera needs to store the analysis data on the integrated SD card of the camera. The data are stored on an MxAnalytics partition and are safely stored in case of a power failure. To format the SD card accordingly, open the Storage on External File Server / Flash Device dialog (Storage Target section).

Configuring the Storage

Tip

You can leave this help page open during the entire process to properly follow the step-by-step instructions.

  • If recording has been activated on the device you would like to format, deactivate recording by selecting the None option as primary target in the Storage Target section.

  • If data recording of MxAnalytics has been activated on the device you want to format, you need to deactivate the recording by selecting the Deactivated option for MxAnalytics in the Storage Options section.

  • Permanently store the settings (Set, then Close at the bottom of the dialog, confirm system prompt) and reboot the camera.

  • Open the Storage on External File Server / Flash Device dialog again and select SD Flash Card in the Format Storage Medium line. Click on the Format button in the same line to start the Formatter Wizard.

  • In the Formatter Wizard dialog, activate the Event Recording Volume as well as the MxAnalytics Volume checkboxes, then set the size of the MxAnalytics partition (or use the preset value).

  • If you want to prevent misuse of the recorded data by reading the device on a computer, you should set a Data Encryption Key.

    Caution

    Only activate the Secure deletion mode - slow option if you would like to erase any existing data without having a chance to recover them. This formatting mode can take up to a couple of hours, depending on the size of the device.

  • Click on OK and confirm the system prompt. The camera shows a progress bar (this may take a couple of minutes). Once the formatting has been completed, the camera shows a summary.

  • Close the dialog and activate the MxAnalytics Storage checkbox in the Storage on External File Server / Flash Device dialog.

  • Proceed by configuring a recording target as shown in the Storage on External File Server / Flash Device help topic.

  • Permanently store the settings (Set, then Close at the bottom of the dialog, confirm system prompt) and reboot the camera.

  • Open the Storage on External File Server / Flash Device dialog and check the status at the bottom of the Storage on External File Server / Flash Device section.

Storage Requirements

The results of MxAnalytics are stored every 15 minutes. When running the analysis 24/7, the resulting volume of data can reach up to 1 GB per month. If you want to analyze longer periods of time, you need to make sure that the MxAnalytics volume is large enough. Note that once the reserved storage capacity of the partition has been reached, the oldest records will be overwritten.

Tip

In order to maximize the storage space for MxAnalytics on the SD card, you can use most of the space for MxAnalytics storage when formatting. For event storage, you can use an external file server or a USB harddisk, for example.


Memorizzazione della configurazione

Fare clic sul pulsante Imposta per attivare le impostazioni e salvarle fino al prossimo riavvio della videocamera.

Fare clic sul pulsante Default per caricare i valori di default di questa finestra di dialogo (opzione non presente in tutte le finestre di dialogo).

Fare clic sul pulsante Ripristina per annullare le modifiche più recenti che non sono state memorizzate in modo permanente nella videocamera.

Fare clic sul pulsante Chiudi per chiudere la finestra di dialogo. Durante la chiusura della finestra di dialogo il sistema verifica eventuali modifiche nella configurazione. Se le rileva chiede di memorizzare in modo permanente l'intera configurazione.


© 2001-2024 MOBOTIX, · http://www.mobotix.com/