Sommario  Guida in linea MOBOTIX

Phone Profiles

Using the Phone Profiles dialog, you can create and manage the profiles for calling phone numbers or SIP addresses.

The profiles thus created are used in the Action Group Overview and File Server Checks dialogs to send notifications using the Phone Call-Out (CL) action.

Note

This feature is not available for Web and Basic models.

Testing the Phone Profiles

Before testing the phone profiles, make sure that you have stored the modifications by clicking on the Set button. Next, select a profile from the Name list in the Test Profile section and click on the Test button.

Description of Parameters

Parameter

Description

Profile name

Enter a unique profile name.

Deleting

To delete a stored profile, click on Remove and confirm your selection by clicking on the Set button.

Phone Number or SIP Address

Enter the phone number for the camera to call.

You can enter multiple phone numbers. The camera then calls the numbers one by one until one of them accepts the call.

Dial Attempts

Defines the maximum number of dial retries.

Value range: 1..10

Dial Timeout

Defines the dial timeout between two retries while dialing in seconds.

SIP Proxy

Please select the SIP account to be used for outbound calls using this number. To make a SIP account accessible here, activate the corresponding Available as Proxy option in the VoIP Settings dialog.

Adding

Click this button to enter more phone numbers. The camera then calls the numbers one by one until one call is completed successfully.

Connection type

Select the Connection Type that should be used for all numbers in this profile (SIP (audio or video)). If you would like to use VoIP for this purpose, activate SIP telephony in the VoIP Settings dialog and enter the appropriate settings (open the VoIP Settings help page to get more information about this topic).

Audio Message

Select one of the audio messages recorded in the Manage Audio Messages dialog.

Confirm call with PIN code

Set a PIN to be entered in order to acknowledge this phone call from the camera. If no PIN is entered (e.g. a voice mailbox answers), the camera will call the next phone number on the list.

After the message has been sent

Hangup

After the voice message has been played back, the connection is terminated.

Listen

After the voice message has been played, the connection remains active and you can listen to what goes on in the room.

Speak

After the voice message has been played, the connection remains active and you can make an announcement.

Intercom

After the voice message has been played, the connection remains active and you can start a conversation.

If not all of these options are shown in the list, open the Speaker and Microphone dialog and activate both the microphone and the speaker.

Camera Remote Control

Activate this option if the camera is supposed to react to touch tone phone commands.

This option is only available, if After the message has been sent is not set to Hangup.

Hangup call after

Set the maximum connection time for a voice message.

Value range: 1 .. 10 minutes

This option is only available, if After the message has been sent is not set to Hangup.

Click on Add new profile at the bottom of the dialog to create a new phone profile.

LED Signals When in VoIP Mode

When using the VoIP interface of the camera, the MOBOTIX camera's LEDs signal the following information, if the LED Setup dialog has been set to the default settings.

LED Signals When in VoIP Mode:

If a voice connection has been established using the VoIP (SIP) interface, the LEDs signal the following:

Adding a Profile

Click on the Add new profile button at the bottom of the dialog to create a new profile. Overtype the proposed name with a name that describes the profile as good as possible; this name is used to identify the profile in other dialogs (e.g. the detail view of the action groups).

Deleting Profiles

In order to delete a profile, activate the Delete checkbox at the top of the profile. The profile will be deleted as soon as you click on Set at the bottom of the dialog.


Memorizzazione della configurazione

Fare clic sul pulsante Imposta per attivare le impostazioni e salvarle fino al prossimo riavvio della videocamera.

Fare clic sul pulsante Default per caricare i valori di default di questa finestra di dialogo (opzione non presente in tutte le finestre di dialogo).

Fare clic sul pulsante Ripristina per annullare le modifiche piĆ¹ recenti che non sono state memorizzate in modo permanente nella videocamera.

Fare clic sul pulsante Chiudi per chiudere la finestra di dialogo. Durante la chiusura della finestra di dialogo il sistema verifica eventuali modifiche nella configurazione. Se le rileva chiede di memorizzare in modo permanente l'intera configurazione.


© 2001-2024 MOBOTIX, · http://www.mobotix.com/